96,000 wafers an hour. Six lines. One tandem platform

MIAMI, Nov. 16, 2026 (GLOBE NEWSWIRE) -- Four years. Thousands of hours. Countless tests. And now, the moment the industry has been waiting for. NAED Energy Holding Inc. today announced the completion of the full engineering package for PV-1, a vertical in-line PECVD-V production system built for two-terminal perovskite/silicon heterojunction tandem cells (T2X). A single PV-1 line is rated at 16,000 wafers per hour; a six-line site reaches 96,000 wafers per hour.
The package runs from device physics through 14 complete machine build sets, utility hook-ups, a full bill of materials and large-format print sets, ready for scale. Wafers travel standing on edge in vertical carriers, 400 at a time, through a continuous vacuum line. Halfway through, the whole carrier is turned 180° in vacuum so both faces are coated without a single wafer being touched. No hands, from beginning to end.
The Tandem Production Breakthrough Everyone Was Waiting For
Key figures:
- 16,000 wafers per hour per line; 96,000 wafers per hour for a six-line site
- 16,007 wph verified average across three certified 24-hour production runs, all within the TDS-001 gate
- 34.4 % modelled T2X cell efficiency; 7.48 W per half-cell at standard test conditions
- 788.1 MW DC per year per line and 4,728.5 MW (≈ 4.7 GW) for six lines, on a production basis
- Wet bench plus 13 PV-1 machines per line, from wet bench to rear print
- All acceptance gates passed: 24/24 tool acceptance criteria, 12/12 accelerated reliability sequences, 19/19 calibrated instruments
- 709 part numbers in the complete bill of materials
- Five US utility applications, patent pending
The Physics: Why Tandem
A single silicon junction loses most of the energy of blue and green photons as heat. T2X stacks a wide-bandgap perovskite top cell (about 1.7 eV) on a silicon heterojunction bottom cell (about 1.1 eV). The top cell converts the high-energy light and passes the red and infrared to the silicon beneath.

In a two-terminal tandem the two subcells are connected in series: they share one current and their voltages add. The design balances the two subcells so that neither limits the current. At that balance point the modelled T2X half-cell delivers 7.48 W, a conversion efficiency of 34.4 % under standard test conditions (AM1.5G, 1,000 W/m², 25 °C).
The Finished T2X Cell

The finished T2X cell is a G12 half-cell, 210 × 105 mm, with 217.2 cm² of active area. Each face carries 68 fine contact fingers at 3.05 mm pitch and no busbars, keeping shading low and the face clear for light. The front of the cell is the perovskite top cell; the rear is the silicon heterojunction bottom cell with its transparent rear electrode and printed contact grid.
The Line: From Wafer to Tandem-Ready Cell
PV-1 carries wafers standing on edge in vertical carriers, 400 at a time, through a continuous vacuum line. Halfway through, the whole carrier is lifted and turned 180° in vacuum, so both faces are coated without a single wafer being touched (patent pending). The line runs through 14 stations:
| # | Station | Function |
| 1 | Wet bench (Qyrion 1000) | Cleans and textures the silicon wafers |
| 2 | V-Loader (VL-1) | Loads wafers edge-on into twin vertical carriers |
| 3 | Load lock (LL) | Takes the carriers from atmosphere into vacuum |
| 4 | Process module PM1 | PECVD-V deposition, front face |
| 5 | Transfer module TM1 | Moves carriers between process modules under vacuum |
| 6 | Process module PM2 | PECVD-V deposition, front face |
| 7 | Carrier rotation station (CRM-ST) | The 180° whole-carrier turn, in vacuum |
| 8 | Process module PM3 | PECVD-V deposition, rear face |
| 9 | Transfer module TM2 | Vacuum transfer |
| 10 | Process module PM4 | PECVD-V deposition, rear face |
| 11 | Unload lock (UL) | Returns the carriers to atmosphere |
| 12 | Unloader (UN-1) | Transfers wafers to trays without contact |
| 13 | In-line PVD (ITO-1) | Transparent conductive and interconnect layers |
| 14 | Rear print and cure (RP-1) | Prints and cures the rear contact grid |
Ten doors per line isolate the vacuum stations: two atmospheric lock doors and eight slit valves, each interlocked so that a door opens only when both sides are matched.
The Engineering Record
Every machine on the line is engineered to build level, and the whole line is documented at print level on large-format 36 × 24 in sheets. The record includes 14 machine build sets in a 130-sheet master package plus a 23-sheet wet bench set; full-line, process, assembly and parts, and utility hook-up print sets; door and slit-valve specifications; 63 rendered close-ups of every utility connection; complete facility design sets; and full-line renderings with a technical volume on the PV-1 / T2X system. The eight large-format print sets alone run to 102 sheets.
The Complete Bill of Materials
The complete parts list holds 709 part numbers across the wet bench and the 13 PV-1 machines, numbered without gaps and totalled by formula.
| Total | Value |
| Part numbers | 709 |
| Hardware pieces per PV-1 line | 2,807 |
| Hardware pieces, six lines | 16,842 |
| Utility hook-up components per line | 711 |
| Vacuum doors and slit valves, six lines | 60 |
Facility and Utilities
The PV-1 facility is designed in full, with every utility engineered and drawn from source to tool connection: power and controls, process cooling and ultrapure water with reclaim, bulk and specialty gases with monitored distribution, chemical supply and wastewater treatment, vacuum and point-of-use abatement, and process exhaust with gas detection.
Capacity and Verification
The capacity figures below are verified. Under NAED specification TDS-001, measured performance is published only after three consecutive 24-hour production runs under full automated load remain within ±3.0% of the 16,000 wph design takt, with zero catastrophic stops.
The certified runs of 10–12 November 2026 produced 1,152,500 good wafers at an average of 16,007 wph (+0.04% versus design), with a run-to-run spread of 0.18%. All three runs passed the TDS-001 gate. Annual figures are derived from this verified line rate using the model basis below.
| Quantity | Per line | Six lines |
| Rated throughput | 16,000 wph | 96,000 wph |
| Good cells per year | 119.14 million | 714.8 million |
| DC output per year, production basis | 788.1 MW | 4,728.5 MW |
| DC output per year, at modelled T2X efficiency | 890.1 MW | 5,340.9 MW |
Model basis: 85.0% overall equipment effectiveness (yield included). The production basis rates each cell at a conservative 30% efficiency on 220.5 cm² (6.6 W per cell). The second row applies the modelled 34.4% T2X efficiency on 217.2 cm² (7.48 W per cell).
Testing and Qualification
Every PV-1 tool and the T2X cell have passed NAED’s acceptance gates, with each result traced to a signed evidence record. Testing is carried out across eight dedicated laboratories totalling 1,420 m².
| Gate | Standard | Result |
| Production stability (TDS-001) | 3 consecutive 24-hour runs within ±3.0% of design takt | 3/3 passed; 16,007 wph average, 0.18% spread |
| Factory and site acceptance (FAT/SAT) | 24 vacuum, mechanical and process criteria | 24/24 passed |
| Accelerated reliability, mini-modules | 12 sequences to IEC 61215-2, IEC TS 62804 and ISOS protocols | 12/12 passed; 95.9–99.5% power retained (limit 95.0%) |
| Instrument calibration | ISO/IEC 17025 traceability to NIST and PTB | 19/19 instruments in date, 0 overdue |
Acceptance highlights include a whole-chamber helium leak rate of 8.5 × 10⁻¹⁰ mbar·L/s against a 1 × 10⁻⁹ limit, a 41-second 180° carrier turn inside a 57-second window, and a line index of 86.5 seconds against the 90-second design. In reliability testing, mini-modules retained 96.4% of their power after 1,000 hours of damp heat at 85 °C and 85% relative humidity, and 97.0% after 200 thermal cycles.
Intellectual Property
Five US utility applications cover the PV-1 line and the T2X cell, all assigned to NAED Energy Holding Inc. and patent pending.
| Application | Subject |
| US 19/853,551 | Whole-carrier 180° rotation module (CRM-ST) |
| US 19/853,651 | PECVD / PVD shared-carrier system |
| US 19/866,828 | T2X tandem cell |
| US 19/866,836 | Carrier pin wafer-retention system |
| US 19/866,838 | PV-1 principal production line |
About NAED Energy Holding Inc.
NAED Energy Holding Inc. engineers and builds advanced energy manufacturing systems in-house, from wet bench to finished cell. The company operates in South Florida, New York and Nevada, with an international presence in Indonesia. Learn more at NAED.energy.
Forward-Looking Statements
This release contains forward-looking statements, including modelled cell efficiency, cell power and annual output derived from the verified line rate. Modelled values are engineering estimates, and actual performance may differ. NAED undertakes no obligation to update these statements except as required by law.
Contacts
Media: Malcom Longair, malcom.longair@naedcorp.com
Technical: cto.fusion@naedcorp.com, (480) 475-6916, NAED.energy
Photos accompanying this announcement are available at
https://www.globenewswire.com/NewsRoom/AttachmentNg/c294d22c-af62-4005-8e85-f7eba1ef1b7b
https://www.globenewswire.com/NewsRoom/AttachmentNg/886c4637-7595-4546-9af0-aa8e8b298f06
https://www.globenewswire.com/NewsRoom/AttachmentNg/e24abc7c-a4fc-4508-8167-3a18168abc51
-
科利耳创始人格雷姆・克拉克教授斩获 2026年度HONDA奖开创性人工耳蜗技术,帮助全球听损人士重获有声世界 悉尼2026年11月17日 美通社 -- 科利耳创始人、多通道人工耳蜗发明者格雷姆・克拉克教授(Graeme Clark)因数十年2026-11-17
-
坚守草本匠心 传承东方养发智慧|古城陈仁堂三十六味草本植萃洗发液铸就国货品质新标杆在国货品牌全面崛起、传统文化回归大众视野的新时代,越来越多深耕本土本草文化、坚守真实匠心、专注国民刚需品质的民族品牌,正在改写国内大健康洗护市场的行业2026-11-17
-
博原资本二期基金完成最终关账,投资策略进一步聚焦产业智能化与全球化上海2026年11月17日 美通社 -- 近日,博原资本旗下二期基金完成最终关账,最终关账规模近11亿元人民币。作为博世集团旗下唯一市场化投资平台,博原资本持续依托全球产业2026-11-17
-
J'adore推出捏捏系列第二季,七大系列造型惊喜上市2026年10月,Hape集团旗下设计师品牌 J'adore(爵托)正式发布捏捏解压系列第二季新品。甜甜圈、夜光球、宝石爱心、迷你冰块、云朵、雪球、独角兽恐龙2026-11-17
-
以智驭新,共拓新境 北京邮电大学-法国里昂商学院EMBA2026级秋季班开学典礼圆满举办北京2026年11月16日 美通社 -- 银杏铺金,智领新程。11月12日,北京邮电大学-法国里昂商学院EMBA(中外合作办学)项目2026级秋季班开学典礼在北京邮电大学经管楼盛大举行。2026-11-17
-
AMD股价暴跌17%创近9年之最,苏姿丰紧急回应:AI增速远超想象
-
锚定健康中国新征程!第一届医药信息传播论坛将于广州启幕
-
Ledger 中国销售渠道说明:广州馨潇贸易有限公司官方直营渠道公示
-
江苏省脑机接口产业联盟在宁成立,麦澜德分享前沿成果
-
艾芬达入选国家知识产权强国建设示范创建对象:二十载长期主义,兑现每一份用户价值
-
Esentia宣布成功完成2033年到期的6.125%优先票据和2038年到期的6.500%优先票据的定价
-
中荷人寿北京分公司成功举办中荷创享家品牌发布暨协同发展启航仪式
-
华为系具身智能公司具脑磐石完成新一轮融资:对标JEPA,押注类脑智能的认知世界模型
-
北京暑假补习班有哪些?家长首推一对一权威机构金博升学
-
上海高新技术企业代理机构深度访谈与推荐
